Slurry pump articles on selection, materials and service, together with the operation manuals and performance charts for the AH, SP, ZJ, ZGB and G series. All can be read online.
Manuals and charts are prepared from the original technical files, with chapter structure and figure numbers matching the printed copies. For technical questions, call +86 188 0321 2220.

Grouped by selection, materials, maintenance and purchasing, and updated as new questions come up.

Five parameters that decide life: flow and head, speed, particle size, material, clearance.

Front liner, frame plate liner and volute liner, and why clearance beats wall thickness.

Different wear mechanisms, different limits: four tests before choosing.

Model, frame, basic number and worn-part dimensions: four checks that prevent wrong parts.

Run near the BEP, watch the clearance, keep the flush water on.

From isolation and flushing to commissioning checks: a list you can work from.
Five manuals, one for each pump family. The online copies match the printed manuals in content, so figure and page numbers can be used side by side.
| Manual | Series covered | Note |
|---|---|---|
| AH / L / G Series Manual | AH Series Heavy Duty Slurry Pump, HH Series High Head Slurry Pump, L Series Light Duty Slurry Pump, DT Series Desulphurisation Pump, G / GH Gravel Pump, AF Series Froth Pump | Primarily AH, L and G, with the same requirements applying to the HH, DT and AF horizontal builds; the most complete of the five. |
| SP Series Sump Pump Manual | SP / SPR Vertical Sump Pump | Sump pumps only: submergence, shaft length, rotation and the ban on low-flow running. |
| ZJ Series Pump Manual | ZJ Series Slurry Pump, SYA / ZJE Filter Press Feed Pump, ZJL Series Vertical Slurry Pump, ZJQ Submersible Slurry Pump | ZJ at the core; SYA/ZJE, ZJL and ZJQ share the same assembly sequence and clearance requirements. |
| ZGB Series Pump Manual | ZGB Series Slurry Pump, 300LPT-SHG Shield Mud Pump | Expeller sealing and multi-stage requirements for ash duty; the 300LPT-SHG refers to it as well. |
| G Gravel Pump Manual | G / GH Gravel Pump, 300LPT-SHG Shield Mud Pump | Single-casing gravel pump, scanned page by page so figure numbers can be matched. |
Find the chapter by the job in hand; full clauses are on the manual index page.
| Chapter | When you look it up |
|---|---|
| Overview and scope | When taking over an unfamiliar pump |
| Construction | Before disassembly |
| Assembly and installation | During installation and piping |
| Shaft seal and lubrication | When adjusting packing or seal water |
| Start-up and operation | At first start-up and shift handover |
| Maintenance and faults | When vibration, leakage or flow loss appears |
Figures are ranges at clear-water test conditions. Selection requires a hydraulic check against the actual medium; pressure, lifting and electrical data follow the supplied documents.
| Document | Contents |
|---|---|
| AH Series Pump Performance Chart | Clear-water performance, motor and outline dimensions |
| SP Series Vertical Pump Chart | Clear-water performance, motor and outline dimensions |
| ZJ Series Pump Performance Chart | Clear-water performance, motor and outline dimensions |
| ZJL Series Vertical Pump Chart | Clear-water performance, motor and outline dimensions |
| DT Series Pump Performance Chart | Clear-water performance, motor and outline dimensions |
| ZJE Filter Press Feed Pump Chart | Clear-water performance, motor and outline dimensions |
| Pump Type Catalogue | All series and models at a glance |
Points to confirm before a selection, a service interval or a fault diagnosis. For any work involving pressure, lifting or electrical equipment, follow the supplied documents and the nameplate.
Medium and solids content, particle size, flow and head, pH and temperature, installation, duty cycle. With a gap, we quote a range rather than a point.
Impeller-to-liner clearance, seal water flow and pressure, bearing temperature and vibration are the hard measures. Schedule by running hours, not by failure.
Suction side first (priming, blockage, cavitation), then rotation and speed, then the wet end. Most flow loss sits in suction and clearance, not the motor.
Selection, price, part numbers, spares, materials and service each have a dedicated guide, with part numbers and an inquiry form at the end.
Packing, expeller and seven seal types by pressure and medium.
Density, head, bore sizing and NPSH checks.
Cost structure, price gaps and an inquiry checklist.
147 impeller, 041 back liner, 083 throat bush.
Tiers, stock arithmetic and register fields.
Grades, construction, failure patterns and acceptance.
Five indicators and three check levels.
Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.