Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Spare Parts/Shaft Seal Parts/Shaft Sleeve
Shaft Sleeve
Shaft Sleeve — part photographBasic no. 075
SPARE PART

Shaft Sleeve

轴套

The shaft sleeve fits over the pump shaft and isolates it from packing friction or mechanical seal contact and from corrosive media. It is one of the most frequently replaced seal-area parts.

Shaft Seal PartsPart code 075
075Basic number
Wear-resistant alloy, stainlessCommon material
Shaft Seal PartsCategory
FUNCTION

What the shaft sleeve does

Function

The shaft sleeve fits over the pump shaft and isolates it from packing friction or mechanical seal contact and from corrosive media. It is one of the most frequently replaced seal-area parts.

Location in the pump

Located in the seal chamber, passing through the stuffing box or mechanical seal, usually with O-rings and a spacer sleeve.

PART CODES

Part codes for the shaft sleeve

Basic number, common full part numbers, the complete code index and model-by-model references.

Basic part number / BASIC NO.
075 / 076

Shaft sleeve

Common full part numbers

D075E075FAM075SH076B075C075

Shaft sleeve basic number 075 and long sleeve 076; D075, E075, FAM075 and SH076 correspond to different frames.

Three-digit basic numbers are fixed for each part type (147 impeller, 110 volute liner, 083 throatbush, 041 frame plate liner, 075 shaft sleeve, 005 bearing assembly). Prefixes vary with pump model and frame, and suffixes denote material: for example E4147 on a 6/4D-AH, F6147 on an 8/6E-AH and G8147 on a 10/8ST-AH. This index is compiled from published part code references for drawing checks and enquiries only; binding part numbers follow the supplied parts book and written confirmation.

Complete basic part number index

Part names link to their own pages; the current part is highlighted.

Show all basic numbersBy basic number
Basic no.Part nameGroup
001Adjusting boltDrive
003Bearing frameDrive
004Bearing housingDrive
005Bearing assembly / rotorDrive
009BearingDrive
011Clamp washerFasteners
012Clamp boltFasteners
013Cover plateWetted
015Cover plate studFasteners
018Front rubber sheathWetted
023Front sheath studFasteners
024End coverDrive
025End cover gasketSeal
026Frame plate liner boltFasteners
027End cover adjusting nutFasteners
028ExpellerSeal
029Relief coverSeal
032Casing / pump bodyWetted
034Casing boltFasteners
036Rear rubber sheathWetted
039Rear sheath studFasteners
040Frame plate liner boltFasteners
041Frame plate liner insertWetted
043Rear sheathWetted
044Split glandSeal
045Gland boltFasteners
046Grease retainerDrive
061Imperial round nutFasteners
062Labyrinth sleeveSeal
063Lantern ringSeal
064O-ringSeal
067Packing spacerSeal
073ShaftDrive
075 / 076Shaft sleeve / long sleeveSeal
078Stuffing boxSeal
080Register gasketFasteners
081Locating plateDrive
083ThroatbushWetted
085Locating wedgeWetted
089Bearing seal ringDrive
090Lip seal ringSeal
108Labyrinth ringSeal
109O-ringSeal
110Volute linerWetted
111PackingSeal
117SpacerDrive
118Front lantern ringSeal
122GasketFasteners
124Volute liner gasketWetted
125Frame plate liner gasketWetted
126Gland studFasteners
132Discharge gasketWetted
138Oil cup seatDrive
147ImpellerWetted

Part codes by pump model

Prefixes vary with pump model and frame. Both model and part names link to their own pages.

Show typical model code setsBy pump model
MATERIALS

Materials used for shaft sleeves

Shaft seal parts control leakage between the pump chamber and the atmosphere. Packing, expeller and mechanical seal options have different seal-water requirements; check sleeve grooves and lantern ring holes first during service.

Material selection

Wear-resistant alloy, stainless or 3Cr13-type martensitic steel, often hardened or coated; rubber-covered versions also exist.

MaterialTypical dutySelection notes
High chrome alloy Cr26 / Cr27 / Cr30Coarse, sharp, highly abrasive ore slurry, tailings and ashVery hard and abrasion resistant; relatively brittle and not suited to large stray impacts
Natural / synthetic wear-resistant rubberFine particles, mildly acidic or alkaline corrosive slurry; noise and vibration dampingElastic and resistant to fine-particle cutting; vulnerable to sharp coarse solids and high temperature - check the temperature limit
Duplex stainless / high-nickel alloyStrongly corrosive, chloride-bearing or high-temperature specialty slurriesCorrosion resistance first; weigh service life and cost against abrasiveness
Polyurethane / ceramic compositeFine but highly abrasive particles, or lightweight wear solutionsLightweight and wear resistant, higher cost; always verify part number and dimensions
Metal vs. rubber parts
WEAR & SERVICE

Wear signs, inspection and replacement

01

Typical wear or failure signs

Grooves under the packing, pitting, corrosion or leakage at O-ring seats. A grooved sleeve quickly destroys new packing.

02

Inspection and replacement

Measure outside diameter and roundness whenever packing or a mechanical seal is changed; replace if grooved, and check seal-water quality and gland tightness.

This section describes general slurry pump principles, selection and maintenance. It does not constitute a commitment regarding particular product parameters, materials, service life or scope of service. Binding values are those in the supplied documentation and in documents confirmed in writing by both parties.
DRAWINGS

Construction and exploded views

Enlarge the exploded and construction views to confirm assembly relationships.

Exploded view
Exploded view
Horizontal construction
Horizontal construction
Vertical construction
Vertical construction
APPLICABLE PUMPS

Applicable pump models

Part codes vary with frame and material; verify against model and part basic number before ordering.

All models
INQUIRY

Shaft Sleeve — quotation and part check

Send the model or worn-part dimensions, or call +86 188 0321 2220 / email sale@pumpq.com.

Request a price

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry