Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Slurry pumps/Filter Press Feed Pump (SYA / ZJE)
SLURRY PUMP SERIES

Filter Press Feed Pump (SYA / ZJE)1480 r/min · 76 m head · chamber filling

A filter press feed duty is a falling curve: high flow and low pressure with empty chambers, then almost no flow and maximum pressure once the cake forms. Both the SYA and ZJE charts on file run at 1480 r/min up to 76 m head, so select on final pressure, not initial flow.

Construction, model range, wetted materials and duty limits for this series. Figures come from the charts and manuals on file; values not published are marked "per supplied documents".

SYA / ZJE filter press feed pump
SYA / ZJE Filter Press Feed Pump
CONSTRUCTION

How this series is built

Horizontal filter press feed pump. SYA / ZJE pumps are designed for filter press feeding, where flow falls and pressure rises as the press fills. They must run stably across a wide duty range; twin-impeller or two-stage builds cover the higher pressure at the end of the cycle.

MODELS & DESIGNATION

Reading the designation, models on file

For example 65SYA75-30: the leading number is a bore designation and the following figures usually denote flow and head/power. In 65ZJE-II the II denotes a two-stage (twin-impeller) build. Codes vary between manufacturers.

PERFORMANCE

Flow, head and speed coverage

Published specifications are stated as flow, head and motor power combinations; exact values follow written confirmation.

ModelMax. power kWQ m³/hH mn r/minMax. eff. %
65ZJE-Ⅱ148027.5 41.4 55.2 69.0 80.022.3Y225S-430
65ZJE-Ⅱ148027.5 41.4 55.2 69.0 80.022.3Y225S-437
80ZJE-Ⅱ148040.0 60.0 80.0 100 11532Y225S-437
80ZJE-Ⅱ148040.0 60.0 80.0 100 11532Y225M-445
100ZJE-Ⅱ148056.0 85.0 113 150 16949Y225M-445
100ZJE-Ⅱ148056.0 85.0 113 150 16949Y225M-455
125ZJE-Ⅱ148070.0 105 140 186 24562.5Y225M-455
125ZJE-Ⅱ148070.0 105 140 186 24562.5Y280S-475
125ZJE-Ⅱ148079.7 119 159 211 27978.2Y280S-475
125ZJE-Ⅱ148079.7 119 159 211 27978.2Y280M-490
125ZJE-Ⅱ148058.0 87.0 116 154 20364.7Y280S-475
125ZJE-Ⅱ148058.0 87.0 116 154 20364.7Y280M-490
Rows are excerpted from the ZJE Filter Press Feed Pump Chart chart on file. Read the full table online; selection follows the supplied documents and written confirmation.
APPLICATIONS

Typical duties

The industry pages behind these duties set out recommended series, wear parts and field checks.

MATERIALS & SEALING

Wetted materials and shaft sealing

Material follows the medium; sealing follows suction pressure and whether dilution is allowed.

SELECTION NOTES

Three checks before choosing this series

WEAR PARTS

Wear parts and basic part numbers

Each part page lists the basic number, material options and applicable models. One basic number maps to different part numbers across frames, so check against the nameplate.

FROM THE MANUAL

Requirements stated in the manual

Excerpts that apply to this series; read the full text on the online reading page.

FAQ

Filter Press Feed Pump (SYA / ZJE): common questions

What is the difference between SYA and ZJE?

Both are filter press feed pumps listed in separate charts at 1480 r/min. Build codes and the press sizes they suit differ; select on chamber volume, feed time and final pressure.

How is feed pump head determined?

Convert the press maximum working pressure into head, then add pipe losses and static lift. A 1.6 MPa press needs roughly 163 m, so a 76 m catalogue value cannot be applied directly.

Can a standard slurry pump be used instead?

It will fill the press but is not recommended long term. A standard pump is efficient at high flow, so running at low flow and high pressure leaves the efficient zone, adding heat, vibration and seal wear.

NEXT STEP

Send the duty and we confirm model and material

Send the medium, particle size and solids content, flow, head, pH and temperature, plus installation conditions (pit depth or line length). For parts, add the pump model or a photo of the worn part.

Request a quotation

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry