Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Slurry pumps/FGD Slurry Pump (DT Series)
SLURRY PUMP SERIES

FGD Slurry Pump (DT Series)Wet FGD · high flow low head · corrosion resistant

The DT series is designed around limestone-gypsum wet FGD slurry: high flow, low head, pH 4-7, elevated chloride and typically no more than 65 C. Charts on file run from 40DT-B20 to 800DT-A96, a wide spread of bore and flow within one series.

Construction, model range, wetted materials and duty limits for this series. Figures come from the charts and manuals on file; values not published are marked "per supplied documents".

DT series FGD slurry pump
DT Series Desulphurisation Pump
CONSTRUCTION

How this series is built

Horizontal, single-stage single-suction FGD circulation pump. The DT series serves limestone-gypsum slurry circulation in wet flue gas desulphurisation. The medium is usually mildly acidic and carries crystalline solids, so both abrasion and corrosion are considered; wetted materials follow pH, chloride content and temperature.

MODELS & DESIGNATION

Reading the designation, models on file

For example 100DT-B45: 100 relates to the discharge bore (mm), DT is the FGD circulation series, B a frame/build code and the trailing figures a size designation. Codes vary slightly between manufacturers.

PERFORMANCE

Flow, head and speed coverage

Published coverage spans several bore and flow classes; exact figures are confirmed against the duty and written documents.

ModelMax. power kWQ m³/hH mn r/minMax. eff. %
800DT-A965955915 7250 9230 10800632.6 653.7 815.2 926.879.7 88.2 88.8 84.110.1
800DT-A964964931 6044 7694 9003367.3 378.8 471.9 536.479.7 88.2 88.8 84.17.7
800DT-A905956104 8527 9170 10690601.7 641.5 640.6 628.876.8 87.6 88.1 80.15.6
800DT-A904965088 7108 7644 8911348.2 371.2 371.0 363.676.8 87.6 88.1 80.14.3
700DT-A855955152 6624 7360 8317359.5 485.7 569.2 536.579.2 86.5 88.0 80.66.5
700DT-A854964295 5522 6135 6933208.2 281.5 330.2 311.479.2 86.5 88.0 80.65.0
700DT-A835963989 5016 5916 6953414.6 441.5 454.8 450.779.4 85.4 87.5 81.57.9
700DT-A834963319 4175 4923 5786239.1 254.3 262.0 259.179.4 85.4 87.5 81.56.0
700DT-A805943760 4757 5293 5974328.6 348.7 355.4 355.182.9 86.2 88.0 84.37.0
Rows are excerpted from the DT Series Pump Performance Chart chart on file. Read the full table online; selection follows the supplied documents and written confirmation.
APPLICATIONS

Typical duties

The industry pages behind these duties set out recommended series, wear parts and field checks.

MATERIALS & SEALING

Wetted materials and shaft sealing

Material follows the medium; sealing follows suction pressure and whether dilution is allowed.

SELECTION NOTES

Three checks before choosing this series

WEAR PARTS

Wear parts and basic part numbers

Each part page lists the basic number, material options and applicable models. One basic number maps to different part numbers across frames, so check against the nameplate.

FROM THE MANUAL

Requirements stated in the manual

Excerpts that apply to this series; read the full text on the online reading page.

FAQ

FGD Slurry Pump (DT Series): common questions

How is a DT pump different from a standard slurry pump?

Hydraulics favour high flow at low head, materials favour corrosion resistance, and seal and flush connections follow FGD start-stop practice. A standard slurry pump in an FGD loop typically fails by corrosion perforation, not wear-through.

Can an FGD pump be rubber lined?

It depends on temperature and chloride. Rubber works at low to moderate temperature with mild corrosion, but not at high temperature or with strong oxidisers; confirm against the assay.

What solids content does gypsum slurry have?

Per the FGD design, typically in the 15-20% solids range, but actual plant data rules. Give both design value and variation band when requesting a selection.

NEXT STEP

Send the duty and we confirm model and material

Send the medium, particle size and solids content, flow, head, pH and temperature, plus installation conditions (pit depth or line length). For parts, add the pump model or a photo of the worn part.

Request a quotation

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry