Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Slurry Pumps/DT Series Desulphurisation Pump/150DT-A50
DT Series Desulphurisation Pump product sheet
DT Series Desulphurisation Pump product sheetModel 150DT-A50
DT Series Desulphurisation Pump · Model details

150DT-A50

DT Series Desulphurisation Pump

The DT series serves limestone-gypsum slurry circulation in wet flue gas desulphurisation. The medium is usually mildly acidic and carries crystalline solids, so both abrasion and corrosion are considered; wetted materials follow pH, chloride content and temperature.

Horizontal Slurry PumpHorizontal, single-stage single-suction FGD circulation pump
62–279Capacity Q m³/h
9.3–44.6Head H m
490–980Speed r/min
MODEL CODE

Reading the code 150DT-A50

Each segment explained against published industry naming conventions.

FieldMeaning
Discharge bore designation150 mm
Series codeDT FGD circulation pump
Build / frame codeA
Size designation50 (definitions vary between manufacturers)
Model codes are explained against common industry naming conventions for reading the letters and numbers only. Bore sizes, frames, materials and performance of a specific build follow the supplied documents and written confirmation.
CONSTRUCTION & DUTIES

Construction and typical duties

DT Series Desulphurisation Pump

Construction

01

High-flow, medium-low head circulation with emphasis on steady operation.

02

Wetted parts balance wear and corrosion resistance, commonly high-chrome alloy or rubber lining.

03

Slurry pH, chloride concentration, temperature and solids content must be checked.

04

Mechanical or packing seals are selected according to flush-water availability.

Typical duties

01

Absorber slurry circulation in wet FGD

02

Limestone and gypsum slurry transfer

03

Mildly corrosive slurry with crystalline solids

Construction drawing
Slurry pump construction drawing
MATERIALS & SEALS

Wetted materials and shaft seals

Wetted materials

High-chrome wear alloy, duplex stainless steel or rubber lining, selected against the combined corrosion and abrasion severity.

Shaft seal

Mechanical seals require clean flush/cooling water; packing seals need periodic gland adjustment and shaft sleeve inspection.

This section describes general slurry pump principles, selection and maintenance. It does not constitute a commitment regarding particular product parameters, materials, service life or scope of service. Binding values are those in the supplied documentation and in documents confirmed in writing by both parties.
PERFORMANCE DATA

Performance data for 150DT-A50

Clear-water data for this model, full series charts and notes from the manuals.

Model specification and technical parameters

ParameterValue / description
Discharge bore designation150 mm
Series codeDT FGD circulation pump
Build / frame codeA
Size designation50 (definitions vary between manufacturers)
ConstructionHorizontal, single-stage single-suction FGD circulation pump
Wetted material optionsHigh-chrome wear alloy, duplex stainless steel or rubber lining, selected against the combined corrosion and abrasion severity.
Shaft seal optionsMechanical seals require clean flush/cooling water; packing seals need periodic gland adjustment and shaft sleeve inspection.
Published series coveragePublished coverage spans several bore and flow classes; exact figures are confirmed against the duty and written documents.

150DT-A50 · rows in Pump Type Catalogue · table 2 (1)

ModelQ m³/hH mn r/minEff. %NPSH mMax. particle mmWeight kg
150DT-A5062-2799.3-44.6490-98065.72.130800

Full performance charts for this series

Complete clear-water performance data for this series. Click to expand; tables scroll horizontally.

DT Series Pump Performance Chart · table 19 rows
Modeln r/minQ m³/hH mShaft power kWEff. %NPSH mMotor modelPower / voltage
800DT-A965955915 7250 9230 1080031.3 29.2 28.8 26.5632.6 653.7 815.2 926.879.7 88.2 88.8 84.110.1YKK6301-10 YKK6302-10 YKK6303-10 YKK710-10800/6000 900/6000 1120/6000 1250/6000
800DT-A964964931 6044 7694 900321.8 20.3 20.0 18.4367.3 378.8 471.9 536.479.7 88.2 88.8 84.17.7YKK5604-12 YKK5604-12 YKK6302-12 YKK6303-12500/6000 500/6000 630/6000 710/6000
800DT-A905956104 8527 9170 1069027.8 24.2 22.6 17.3601.7 641.5 640.6 628.876.8 87.6 88.1 80.15.6YKK6301-10 YKK6301-10 YKK6301-10 YKK6301-10800/6000 800/6000 800/6000 800/6000
800DT-A904965088 7108 7644 891119.3 16.8 15.7 12.0348.2 371.2 371.0 363.676.8 87.6 88.1 80.14.3YKK5603-12 YKK5604-12 YKK5604-12 YKK5603-12450/6000 500/6000 500/6000 450/6000
700DT-A855955152 6624 7360 831720.3 23.3 25.0 19.1359.5 485.7 569.2 536.579.2 86.5 88.0 80.66.5YKK5601-10 YKK5603-10 YKK6301-10 YKK5604-10500/6000 630/6000 800/6000 710/6000
700DT-A854964295 5522 6135 693314.1 16.2 17.4 13.3208.2 281.5 330.2 311.479.2 86.5 88.0 80.65.0YKK5601-10 YKK5603-10 YKK6301-10 YKK5604-10500/6000 630/6000 800/6000 710/6000
700DT-A835963989 5016 5916 695330.3 27.6 24.7 19.4414.6 441.5 454.8 450.779.4 85.4 87.5 81.57.9YKK5602-10 YKK5602-10 YKK5602-10 YKK5602-10560/6000 560/6000 560/6000 560/6000
700DT-A834963319 4175 4923 578621.0 19.1 17.1 13.4239.1 254.3 262.0 259.179.4 85.4 87.5 81.56.0YKK5004-12 YKK5004-12 YKK5601-12 YKK5601-12315/6000 315/6000 355/6000 355/6000
700DT-A805943760 4757 5293 597426.6 23.2 21.7 18.4328.6 348.7 355.4 355.182.9 86.2 88.0 84.37.0YKK5004-10 YKK5004-10 YKK5004-10 YKK5004-10450/6000 450/6000 450/6000 450/6000
DT Series Pump Performance Chart · table 211 rows
Modeln r/minQ m³/hH mShaft power kWEff. %NPSH mMotor modelPower / voltage
700DT-A804963139 3972 4420 498818.6 16.2 15.1 12.9191.8 203.3 206.5 207.982.9 86.2 88.0 84.35.4YKK5002-12 YKK5002-12 YKK5003-12 YKK5003-12250/6000 250/6000 280/6000 280/6000
700DT-F785944693 6042 7221 811121.0 18.5 14.9 12.3333.8 353.1 347.6 332.580.4 86.2 84.3 81.79.6YKK5004-10 YKK5004-10 YKK5004-10 YKK5004-10450/6000 450/6000 450/6000 450/6000
700DT-F784963919 5045 6030 677314.7 12.9 10.4 8.5195.1 205.6 202.6 191.980.4 86.2 84.3 81.77.3YKK5002-12 YKK5003-12 YKK5002-12 YKK5002-12250/6000 280/6000 250/6000 250/6000
600DT-A825953300 4700 5300 560027.8 24.7 21.7 20.4343.2 358.0 362.9 368.272.8 88.3 86.3 84.54.0YKK5601-10 YKK5601-10 YKK5601-10 YKK5601-10500/6000 500/6000 500/6000 500/6000
600DT-A824902718 3871 4365 461218.9 16.8 14.7 13.8192.2 200.6 202.5 205.172.8 88.3 86.3 84.53.0YKK5003-12 YKK5003-12 YKK5003-12 YKK5003-12280/6000 280/6000 280/6000 280/6000
500DT-A855912040 3400 408026.8 24.4 22.0204.5 266.7 305.272.8 84.7 80.14.1Y450-10 Y450-10 Y500-10250/6000 355/6000 400/6000
500DT-A854931702 2836 340318.6 17.0 15.3118.4 155.0 177.072.8 84.7 80.13.1Y450-12 Y450-12 Y450-12220/6000 220/6000 220/6000
350DT-A787401332 2431 286551.1 44.5 39.6289.6 377.7 408.764.0 78.0 75.66.5Y450-8 Y500-8 Y500-8355/6000 500/6000 500/6000
350DT-A785901062 1938 228432.5 28.3 25.2146.9 191.5 207.364.0 78.0 75.63.5Y450-10 Y450-10 Y450-10185/6000 250/6000 280/6000
300DT-A609891170 1779 240353.1 47.1 36.1235.6 281.4 313.371.8 81.1 75.48.4Y400-6 Y400-6 Y400-6315/6000 355/6000 400/6000
300DT-A60742878 1335 180329.9 26.5 20.399.6 118.8 132.271.8 81.8 75.44.3Y355M1-8 Y355M2-8 Y355M2-8132/380 160/380 160/380
DT Series Pump Performance Chart · table 324 rows
Modeln r/minQ m³/hH mShaft power kWEff. %NPSH mMotor modelPower / voltage
350DT-A5359082212.240.267.96.5Y315M1-1055/380
350DT-A53590121310.042.477.86.5Y315M1-1055/380
350DT-A5359014168.643.676.06.5Y315M1-1055/380
350DT-A534906808.422.967.93.7Y250M-830/380
350DT-A5349010046.924.277.83.7Y250M-830/380
350DT-A5349011725.924.776.03.7Y250M-830/380
350DT-A5159262610.829.063.46.5Y315S-1045/380
350DT-A515928889.431.372.46.5Y315S-1045/380
350DT-A5159211587.432.671.56.5Y315S-1045/380
350DT-A514905187.416.563.43.7Y250M-830/380
350DT-A514907386.417.772.43.7Y250M-830/380
350DT-A514909585.118.671.53.7Y250M-830/380
300DT-A60989117053.1235.671.88.4Y400-6280/6000
300DT-A60989177947.1281.481.18.4Y400-6280/6000
300DT-A60989240336.1313.375.48.4Y400-6400/6000
300DT-A6074287829.999.671.84.3Y355M1-8132/380
300DT-A60742133526.5118.881.14.3Y355M2-8160/380
300DT-A60742180320.3132.275.44.3Y355M2-8160/380
200DT-B4598027630.436.362.93.3Y280S-645/380
200DT-B4598055125.647.580.83.3Y280M-655/380
200DT-B4598063822.850.977.83.3Y315S-675/380
200DT-B4573020616.915.162.92.0Y225M-822/380
200DT-B4573041014.219.680.82.0Y250M-830/380
200DT-B4573047512.721.177.82.0Y250M-830/380
DT Series Pump Performance Chart · table 433 rows
Modeln r/minQ m³/hH mShaft power kWEff. %NPSH mMotor modelPower / voltage
150DT-A601480329150.0232.157.97.5Y355L1-4280/380
150DT-A601480576136.3308.169.47.5Y400-4355/6000
150DT-A601480704129.1350.170.77.5Y400-4450/6000
150DT-A6098021865.867.557.93.4Y315M-690/380
150DT-A6098038159.889.469.43.4Y315L1-6110/380
150DT-A6098046656.6101.670.73.4Y315L2-6132/380
150DT-A6073016236.527.857.92.1Y280S-837/380
150DT-A6073028433.237.069.42.1Y280M-845/380
150DT-A6073034731.442.070.72.1Y315S-855/380
150DT-B5599028053.764.863.23.7Y315M-690/380
150DT-B5599051748.088.376.53.7Y315L1-6110/380
150DT-B5599063045.9100.878.13.7Y315L2-6132/380
150DT-B5574020930.027.063.22.3Y280S-837/380
150DT-B5574038726.836.976.52.3Y280M-845/380
150DT-B5574047125.742.278.12.3Y315S-855/380
150DTG-A5098012344.627.654.13.5Y250M-637/380
150DTG-A5098022140.136.965.43.5Y280S-645/380
150DTG-A5098027937.243.465.23.5Y280M-655/380
150DTG-A507309224.711.454.12.1Y200L-815/380
150DTG-A5073016522.315.365.42.1Y225M-822/380
150DTG-A5073020820.617.965.22.1Y250M-830/380
150DT-A40149026061.268.863.06.5Y280M-490/380
150DT-A40149044053.888.273.16.5Y315S-4110/380
150DT-A40149050350.795.472.86.5Y315-4110/380
150DT-A4098017126.519.663.02.6Y225M-630/380
150DT-A4098028923.325.173.12.6Y250M-637/380
150DT-A4098033121.927.172.82.6Y250M-637/380
100DT-A601490152147.0133.445.64.9Y315M2-4160/380
100DT-A601490256138.5170.956.54.9Y315L2-4200/380
100DT-A601490305131.7188.957.94.9Y355M1-4220/380
100DT-A6099010164.939.145.62.4Y280S-645/380
100DT-A6099017061.250.156.52.4Y315S-675/380
100DT-A6099020358.155.557.92.4Y315S-675/380
DT Series Pump Performance Chart · table 530 rows
Modeln r/minQ m³/hH mShaft power kWEff. %NPSH mMotor modelPower / voltage
100DT-A45148010083.546.449.04.6Y250M-455/380
100DT-A45148019571.646.458.74.6Y280S-475/380
100DT-A45148022866.164.857.54.6Y280M-490/380
100DT-A459806636.613.449.02.2Y200L1-618.5/380
100DT-A4598012931.418.858.72.2Y225M-630/380
100DT-A4598015129.020.757.52.2Y225M-630/380
100DT-A45B14808876.443.642.06.0Y250M-455/380
100DT-A45B148016665.256.951.86.0Y280S-475/380
100DT-A45B148021954.366.548.76.0Y280M-490/380
100DT-A45B9705732.812.142.02.4Y200L1-618.5/380
100DT-A45B97010928.016.051.82.4Y200L2-622/380
100DT-A45B97014423.318.848.72.4Y225M-630/380
100DTG-B45C148011266.649.740.97.5280S-475/380
100DTG-B45C148019862.363.153.27.5Y280S-475/380
100DTG-B45C148023358.769.553.67.5Y280M-490/380
100DTG-B45C9807429.214.440.93.6Y200L1-618.5/380
100DTG-B45C98013127.318.353.23.6Y225M-630/380
100DTG-B45C98015425.720.153.63.6Y225M-630/380
100DT-B40148012961.037.756.93.5Y225M-445/380
100DT-B40148021956.148.768.73.5Y280S-475/380
100DT-B40148026853.655.670.43.5Y280S-475/380
100DT-B409708526.210.756.91.7Y180L-615/380
100DT-B4097014424.113.868.71.7Y200L2-622/380
100DT-B4097017682.965.858.71.7Y200L2-622/380
100DTG-B38CS14808594.147.645.87.1Y250M-455/380
100DTG-B38CS148013690.760.056.07.1Y280S-475/380
100DTG-B38CS148017182.965.858.77.1Y280M-490/380
100DTG-B38CS9705640.413.545.83.4Y200L1-618.5/380
100DTG-B38CS9708939.016.956.03.4Y200L2-622/380
100DTG-B38CS97011235.618.558.73.4Y225M-630/380
DT Series Pump Performance Chart · table 630 rows
Modeln r/minQ m³/hH mShaft power kWEff. %NPSH mMotor modelPower / voltage
100DT-A35148016345.933.560.94.1Y225M-445/380
100DT-A35148027841.543.771.94.1Y250M-455/380
100DT-A35148032339.247.173.24.1Y250M-455/380
100DT-A3597010719.79.460.91.9Y180L-615/380
100DT-A3597018217.812.371.91.9Y200L1-618.5/380
100DT-A3597021216.813.373.21.9Y200L1-618.5/380
80DT-A3614808647.123.347.73.2Y200L-430/380
80DT-A36148015142.028.560.73.2Y225S-437/380
80DT-A36148016739.929.362.03.2Y225S-437/380
80DT-A369705620.26.547.41.5Y160L-611/380
80DT-A369709918.08.060.71.5Y160L-611/380
80DT-A3697010917.18.262.01.5Y160L-611/380
65DT-A4014807163.226.246.74.5Y225S-437/380
65DT-A40148014157.535.662.14.5Y225M-445/380
65DT-A40148015954.638.162.14.5Y225M-445/380
65DT-A409704727.17.445.72.1Y160L-611/380
65DT-A409709224.710.062.12.1Y180L-615/380
65DT-A4097010423.510.762.12.1Y180L-615/380
65DT-A3014704435.69.146.74.6Y160L-415/380
65DT-A3014707932.612.854.64.6Y180M-418.5/380
65DT-A3014709930.715.453.84.6Y180L-422/380
65DT-A309602915.22.645.72.2Y132M2-65.5/380
65DT-A309605113.93.554.62.2Y132M2-65.5/380
65DT-A309606413.14.253.82.2Y132M2-65.5/380
50DT-B4014705261.020.542.02.5Y180L-422/380
50DT-B4014709055.024.954.02.5Y200L-430/380
50DT-B40147010053.026.255.02.5Y200L-430/380
50DT-B409703527.06.142.01.2Y160M-67.5/380
50DT-B409706024.07.354.01.2Y160M-67.5/380
50DT-B409706623.57.755.01.2Y160M-67.5/380
DT Series Pump Performance Chart · table 730 rows
Modeln r/minQ m³/hH mShaft power kWEff. %NPSH mMotor modelPower / voltage
50DT-A3014603436.37.843.11.6Y160M-411/380
50DT-A3014605531.99.948.51.6Y160L-415/380
50DT-A3014607826.412.445.41.6Y180M-418.5/380
50DT-A309602215.72.243.10.8Y132M1-64/380
50DT-A309603613.82.848.50.8Y132M2-65.5/380
50DT-A309605111.43.545.40.8Y132M2-65.5/380
40DT-A25295035.588.620.741.3-Y200L1-230/380
40DT-A25295058.873.527.742.5-Y200L2-237/380
40DT-A25295074.760.831.239.6-Y200L2-237/380
40DT-A25144017.321.12.441.32.6Y112M-44/380
40DT-A25144028.717.53.242.52.6Y132S-45.5/380
40DT-A25144036.514.53.639.62.6Y132S-45.5/380
40DT-B20293016.657.56.440.93.5Y160M1-211/380
40DT-B20293033.349.98.553.03.5Y160M2-215/380
40DT-B20293037.147.19.252.03.5Y160M2-215/380
40DT-B2014308.113.70.740.90.9Y90L-41.5/380
40DT-B20143016.311.91.053.00.9Y100L1-42.2/380
40DT-B20143018.111.21.152.00.9Y100L1-42.2/380
250DT-A2514409.621.61.733.27.1Y100L2-43/380
250DT-A25144017.816.62.138.07.1Y112M-44/380
250DT-A25144019.913.92.233.87.1Y112M-44/380
250DT-A259106.08.60.433.23.3Y90S-60.75/380
250DT-A2591011.26.60.538.03.3Y90L-61.1/380
250DT-A2591012.55.50.633.83.3Y90L-61.1/380
25DT-A1529009.234.42.632.75.3Y132S1-25.5/380
25DT-A15290017.129.53.341.85.3Y132S1-25.5/380
25DT-A15290019.327.13.540.85.3Y132S1-25.5/380
25DT-A1513904.47.90.332.71.3Y801-40.55/380
25DT-A1513908.26.80.441.81.3Y802-40.75/380
25DT-A1513909.36.20.440.81.3Y802-40.75/380
Pump Type Catalogue · table 169 rows
ModelMax. power kWQ m³/hH mn r/minEff. %NPSH mMax. particle mmWeight kg
350ZJ-I-F100560526-233914.9-62.8300-59077.64.4965470
350ZJ-I-C1045601335-330036.6-66.9490-59077.67.31506750
350ZJ-I-C100710834-350211.1-60.0300-59373.07.41506710
350ZJ-I-A857101025-374112.3-62.3400-74277.210.5714800
350ZJ-I-A80630837-35758.4-56.4400-74275.710.5704100
300ZJ-I-A100450464-182615.3-65.2300-59081.13.0884580
300ZJ-I-B100450464-182615.3-65.2300-59076.23.01124580
300ZJ-I-A95400441-173513.8-58.8300-59078.13.0884535
300ZJ-I-A90560505-184421.2-79.9400-73082.83.9854656
300ZJ-I-C90400604-239210.9-50.9300-59078.63.61505060
300ZJ-I-A85450477-174218.9-71.3400-73079.83.8854525
300ZJ-I-A70630635-233316.0-76.8490-98080.43.9923274
300ZJ-I-A65500589-216613.8-66.2490-98077.43.7923245
300ZJ-I-A56250395-15689.7-46.0490-98080.93.5962340
250ZJ-I-A103560402-157329.7-110.5400-73074.52.8695230
250ZJ-I-A96560403-146625.4-93.7400-73077.83.5694200
250ZJ-I-A90450378-137422.3-82.4400-73073.83.4694145
250ZJ-I-A85800376-150430.1-128.7490-98076.53.5764100
250ZJ-I-A83800367-146928.7-122.7490-98075.53.5764085
250ZJ-I-A80710354-141626.7-114.0490-98073.53.4764060
250ZJ-I-C80450451-17907.4-38.3300-59275.13.31204832
250ZJ-I-A78630415-179621.1-102.5490-98071.53.2764045
250ZJ-I-A75560300-148020.8-97.5490-98077.53.0722760
250ZJ-I-A73500292-144119.7-92.4490-98076.53.0722745
250ZJ-I-A70450280-138118.1-84.9490-98074.52.9722725
250ZJ-I-A68450272-134217.1-80.1490-98073.52.7722712
250ZJ-I-A65315299-124915.4-71.0490-98076.93.0722520
250ZJ-I-A63315290-121114.4-66.7490-98075.93.0722508
250ZJ-I-A60280276-115313.1-60.5490-98073.92.8722490
200ZJ-I-A85560221-90732.0-133.7490-98070.52.8543844
200ZJ-I-A75355225-90022.8-102.9490-98074.13.0562880
200ZJ-I-A73355219-87621.6-97.5490-98073.13.0562865
200ZJ-I-A70315205-97619.4-86.4490-98075.62.8562256
200ZJ-I-A68315199-94818.3-81.5490-98074.62.8562248
200ZJ-I-A65250235-95016.4-72.0490-98079.62.5622000
200ZJ-I-A63250228-92115.4-67.6490-98078.62.5621988
200ZJ-I-A60185218-87013.9-62.0490-98083.52.5621800
200ZJ-I-A58185211-84113.0-57.9490-98082.52.5621791
150ZJ-I-A71220142-55221.8-93.8490-98069.82.4482093
150ZJ-I-A7018593-40120.2-91.2490-98062.32.0371943
150ZJ-I-A65200150-60017.4-75.7490-98070.82.5481892
150ZJ-I-A63185146-58216.3-71.1490-98069.82.5481880
150ZJ-I-A60160135-55014.7-63.5490-98075.92.5481760
150ZJ-I-A58132131-53213.7-59.3490-98074.92.5481730
150ZJ-I-C58160134-59612.8-61.0490-98069.12.0751825
150ZJ-I-A5711095-42713.2-56.3490-98067.81.8321820
150ZJ-I-A55110124-50412.3-53.4490-98072.92.3481810
150ZJ-I-A5075115-4609.5-43.1490-98076.82.5481198
150ZJ-I-A4875111-4428.7-39.7490-98075.82.5481185
150ZJ-I-C42132142-55012.1-62.8700-148077.12.2691070
100ZJ-I-A5016085-36020.5-100.2700-148069.62.534987
100ZJ-I-A4613279-33117.3-84.8700-148067.62.334973
100ZJ-I-A429066-27514.7-70.8700-148071.02.535625
100ZJ-I-A397561-25512.6-61.0700-148039.02.435615
100ZJ-I-B429083-36512.7-66.8700-148071.62.540635
100ZJ-I-A365561-2459.7-49.5700-148071.62.032597
100ZJ-I-A334556-2258.2-41.6700-148069.61.832590
80ZJ-I-A5216051-24222.1-109.8700-148056.32.121993
80ZJ-I-A427561-20414.4-70.4700-148066.72.524599
80ZJ-I-A395557-18912.4-60.7700-148064.72.424589
80ZJ-I-A364546-1909.6-51.4700-148067.72.524559
80ZJ-I-A333743-1748.0-43.2700-148065.72.324552
65ZJ-I-A301523-797.4-34.8700-146063.52.019450
65ZJ-I-A271120-716.0-28.2700-146061.51.819445
50ZJ-I-A509027-11122.3-110.7700-148045.13.013941
50ZJ-I-A465523-9417.9-85.8700-148044.71.414657
50ZJ-I-A3318.512-547.7-42.5700-148042.12.913395
40ZJ-I-A19158.0-34.912.8-57.11430-293058.81.311116
40ZJ-I-A177.54.5-23.49.1-44.61400-290052.42.51190
Pump Type Catalogue · table 268 rows
ModelQ m³/hH mn r/minEff. %NPSH mMax. particle mmWeight kg
1000DT-A1308857-1600014.6-32.0310-44086.16.011812400
900DT-F1104907-140768.5-32.7300-49088.36.5969480
800DT-A1057412-1480016.0-41.5450-59586.74.0966680
800DT-A1005983-1230012.7-37.2400-59587.77.81506660
800DT-A935169-121689.3-32.2400-59585.69.1666650
800DT-A904104-106907.8-27.8400-59586.44.3885940
700DT-A934083-105609.3-35.0400-59583.26.1705660
700DT-A903551-898810.0-33.8400-59586.75.6685400
700DT-A832677-64918.7-30.2400-59585.96.0705900
700DT-B783378-720010.0-21.8400-59584.74.3655040
650DT-B803961-767315.6-38.3550-74086.39.6604120
600DT-A821664-56005.2-27.8300-59588.32.21523960
550DT-A752622-656311.6-38.2490-74081.55.7602680
550DT-A702298-57088.0-30.1450-74082.24.5602666
500DT-A761555-38819.9-27.9450-59576.84.5583512
500DT-A751655-430012.2-40.1490-74083.85.3582502
500DT-A701908-43999.3-32.5490-74276.06.0552900
450DT-A701655-420010.3-33.3490-74084.25.5562550
400DT-A651134-33308.8-31.1490-74280.15.2602340
400DT-A551020-26405.6-29.8490-98081.77.1421675
350DT-A78720-286511.6-51.1400-74078.03.51042800
350DT-A65750-24807.3-32.1400-74084.72.8922240
350DT-A58668-19705.9-24.3400-74082.52.8992250
350DT-A52963-22008.8-30.8590-98082.93.7501238
350DT-A48638-18007.0-26.7590-98075.94.0501222
300DT-A70995-282827.5-75.0700-99377.65.3922470
300DT-A60574-23848.7-52.0490-98981.14.3962300
300DT-A50440-17506.1-32.8490-98081.72.2801140
300DT-A45456-16204.2-25.0490-98075.53.4401100
250DT-A75300-148020.8-97.5490-98077.53.0722500
250DT-A52333-12208.1-42.4490-98081.62.3651004
250DT-A48480-11036.4-25.6490-98078.53.7421030
250DT-A45221-8045.0-27.0490-98068.24.1561150
250DT-B45297-9905.0-27.0490-98076.63.7641150
200DT-A60237-86819.2-60.2590-98077.02.7521500
200DT-B45136-6395.5-30.1490-99080.82.051755
200DT-B40208-6484.0-21.0490-98077.22.636720
150DT-A60156-70428.9-150.0700-148070.72.1391450
150DT-B55139-63011.3-53.7490-99078.12.356815
150DT-A5062-2799.3-44.6490-98065.72.130800
150DT-A40122-50311.2-61.2700-149073.12.640550
150DT-A30115-33010.9-31.4950-148076.72.130326
150DT-A27117-2998.2-24.0950-148075.42.016320
100DT-A6071-30529.1-147.0700-148057.92.418960
100DT-A5085-36020.5-100.2700-148069.62.534880
100DT-A4547-22814.8-83.5700-148058.72.222550
100DT-B4061-26812.0-61.0700-148070.41.729530
100DT-A3577-3238.8-45.9700-148073.21.942520
100DT-A3077-2815.5-29.8700-148066.82.545515
80DT-A3641-1678.9-47.1700-148062.41.516420
65DT-A4034-15911.5-60.1700-148062.12.116476
65DT-A3021-997.0-35.6700-147054.62.219250
50DT-A5027-11122.3-110.7700-148045.13.013700
50DT-A4521.6-93.615.2-81.0700-148048.43.69.5544
50DT-B4024.5-99.512.0-60.7700-147055.03.114406
50DT-A3016.0-78.05.8-35.1700-146048.50.816210
50DT-A30B11.0-70.06.2-36.0700-146051.22.016200
40DT-A40B12.0-39.011.0-64.3700-147034.93.310270
40DT-B3513.8-55.07.3-45.5700-148034.72.26220
40DT-B35B10.0-40.013.0-46.6700-146041.22.88220
40DT-A3010.4-32.59.5-34.0700-147037.53.08230
40DT-B30B9.3-35.36.1-35.3700-147041.01.812220
40DT-A2511.5-36.56.4-21.1960-144042.51.59175
40DT-B207.9-37.110.7-57.51400-293053.00.9785
40DT-A197.8-34.912.3-57.11400-293058.81.21190
40DT-A174.6-23.49.2-44.61400-290052.42.51185
25DT-A254.7-19.93.3-21.6700-144038.03.3570
25DT-A153.8-16.05.4-33.51390-290040.11.3867
Pump Type Catalogue · table 313 rows
ModelMax. power kWQ m³/hH mn r/minEff. %NPSH mMax. particle mmWeight kg
150TL-A353099-3643.0-17.9490-98069.0/15712
100TL-A344574-2935.5-36.8700-148065.8/14502
80TL-A4511059-28612.5-81.6700-149058.4/15785
80TL-A364550-2017.3-45.5700-148058.2/12645
65TL-A404530.2-142.810.2-62.6700-148050.0/12658
65TL-A3018.518-985.9-34.7700-147053.7/8436
50TL-A455521.9-117.310.4-78.4700-148039.9/9.5778
50TL-B403015-658.6-58.3700-147034.1/9502
50TL-A352219-876.8-45.3700-147048.1/15498
40TL-A3518.59.4-47.67.2-43.9700-147038.7/7524
40TL-B255.54.9-22.93.9-21.5700-144037.6/8225
40TL-A2144.6-25.93.3-17.0700-144044.6/10210
25TL-A155.54.3-19.33.9-30.81390-290029.8/8195
Pump Type Catalogue · table 422 rows
ModelQ m³/hH mn r/minEff. %Inlet mmOutlet mmNPSH mMax. particle mm
100ND100-25020-50800-98065-70150100< 3.050
150ND240-65024-61980-148062.5-71.7250150< 3.570
200ND610-156029-62650-90061-62.4250200< 4.5143
250N720-180030-75500-75065-76350250< 4.0125
250ND600-200021-59490-74068.5-79.8350250< 4.0146
300N1600-220040-65400-55072-78400300< 4.5135
300ND1500-375029-65400-55069-73420300< 4.5201
350ND1700-275024-58400-59077-81450350< 4.0122
450N3150-650040-65350-50074-80600450< 4.5220
450ND3100-520030-66350-49068.5-75.2600450< 4.5115
500N5900-910040-75350-45074-80650500< 4.8245
500ND4000-700020-41220-32575-82650500< 4.5203
600N6500-1200045-70300-40078-84700600< 4.8240
600ND4800-890020-42350-42082-85700600< 4.6240
650ND8500-1430023-65300-45082.3-85800650< 4.6256
700N10500-1640040-75300-38080-85800700< 6.0260
700ND8000-1300020-45240-28081-84800700< 5.3260
800N14500-2180055-80300-36081-85900800< 6.0275
800ND9700-1540020-40200-28082-84900800< 5.3275
900N21000-3100045-70200-28080-851000900< 5.8300
900ND12000-2150020-40160-21082-8811001000< 6.0300
1000N24350-3900026-78210-29082-8511001000< 6.0320
Clear-water performance data for reference only; binding values follow the supplied technical documents and written confirmation.
FROM THE MANUAL

Notes from the product manuals

Compiled from the AH / L / G, SP, ZJ and ZGB pump manuals, with links to the full texts.

General construction, installation and operation

01 · Overview and scope

Horizontal slurry pumps are overhung centrifugal pumps for abrasive or corrosive slurry, widely used in metallurgy, mining, petrochemical, coal, power, dredging, building materials and municipal works. Families cover heavy duty (AH, HH), light duty (L), gravel / dredging (D, G) and rubber-lined (AHR, LR, MR) builds. Pumps may be staged in series within the allowable working pressure.

02 · Construction

Heavy duty AH and HH pumps use a double casing: an outer pressure-retaining casing and cover in grey or ductile iron, vertically split and bolted, plus replaceable wear liners (impeller, volute liner, throat bush and frame plate liner) in metal or rubber. The discharge can be rotated in eight positions at 45 degree intervals. D and G gravel pumps use a single casing with all wetted parts in wear-resistant metal. Apart from the wet end, all horizontal types share the same frame and bearing assembly, with a large-diameter shaft and short overhang.

03 · Assembly and installation

Preheat bearing inner rings to no more than 120 C during assembly and seat them firmly against the shaft shoulder or grease retainer. Inner rings, outer rings and spacers of double-row tapered roller bearings form a matched set and must not be interchanged. Wet-end assembly order: seals, frame plate liner with its locating nuts, impeller, volute liner clamped in place, then throat bush and cover plate. Lift crated pumps by the marked sling points without shock or excessive tilt; lifting eyes on the casing are for dismantling the casing only, never for lifting the complete pump.

04 · Shaft seal and lubrication

Three shaft seal arrangements are common: expeller, packed gland and mechanical seal. The expeller seal suits single-stage pumps (or the first stage of a series set) where inlet positive pressure is below 10 percent of discharge pressure; it needs no seal water and does not dilute the slurry. A packed gland is simple to service but requires seal water. A mechanical seal gives the best sealing and requires cooling water. A packed gland comprises the stuffing box, shaft sleeve, spacer, O-rings, packing, packing spacer, lantern ring and gland. Bearings are grease or oil lubricated, with oil lubrication preferred for high temperature or large pumps.

05 · Start-up and operation

Before start-up check that foundation and coupling bolts are tight, turn the shaft by hand in the direction of rotation without rubbing, verify motor rotation against the arrow on the casing, and align the V-belts square to the pulleys. Starting on clean water is preferable before slurry is introduced. During operation watch the instruments for flow, velocity and current and correct any abnormality. Where possible flush with clean water before stopping, then stop the pump before closing the valve. For vertical sump pumps, turn on the guide bearing flush water five minutes before starting and close it five minutes after stopping.

06 · Maintenance and faults

Check impeller-to-throatbush clearance, bearing temperature and lubrication, seal water pressure and flow, and wear of wetted parts on a regular basis. A worn impeller reduces flow and head and raises vibration and noise, so adjust the clearance or replace the wear parts. Typical faults are insufficient flow or head, bearing overheating, vibration, seal leakage and cavitation, usually caused by blockages, wrong rotation, low speed, air ingress on the suction side, inadequate NPSH or loss of dynamic balance. Record basic part numbers and material suffixes and verify them against the pump model and supplied documents.

Series-specific notes for DT Series Desulphurisation Pump

01

Desulphurisation circulation pumps handle gypsum slurry containing chloride ions and mild acid, so wetted parts must resist both abrasion and corrosion, commonly using high-chrome alloy or rubber linings.

02

Selection must check flow, head, NPSH and motor power together with solids content, pH and chloride concentration.

Source text excerpts

Original manual text

Extracts from the original manuals are shown in the Chinese edition; the full texts are available via the links below.

Read the source documents online

WEAR PARTS

Wear parts for this series

Open each part page for function, material and replacement notes.

INQUIRY

150DT-A50 — quotation and part check

Send the model or worn-part dimensions, or call +86 188 0321 2220 / email sale@pumpq.com.

Request a price

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry