Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Products/Other Wear Parts
PRODUCTS · OTHER WEAR PARTS

Other Wear PartsCover plates, stuffing boxes, frames and fasteners: small parts, big effect on downtime

An unplanned stop is often caused not by a worn-through impeller but by a seized release ring, a broken bolt or a leaking stuffing box joint. These items cost little but decide whether maintenance finishes on schedule.

The practical answer is to include them in a standing spare list: count the small parts by pump and frame size and keep one or two sets, so a single missing item does not stop the whole unit.

Slurry pump small wear parts
Other Wear Parts
SCOPE

What this category covers

Part / structureDescription
Cover plate and jointsClose the chamber and connect pump head to frame
Stuffing box and glandCarry the seal and match the shaft sleeve
Frame and end coverSupport the bearing assembly and form the oil chamber
Fasteners and locatorsRelease ring, lock nut, clamp washer and gaskets
MATERIALS

Typical materials for each part

PartFunction in the pumpTypical material
Cover PlateThe cover plate closes the suction side of the pump end, connects to the suction pipe and forms the inlet passage with the front liner.Ductile iron or cast steel, with the suction-side inner surface protected by the front liner or volute liner.
Stuffing BoxThe stuffing box houses packing, the lantern ring and the gland, forming the packing seal chamber and admitting seal water for cooling, lubrication and flushing.Cast iron, cast steel or wear/corrosion-resistant alloy, with the bore matched to the shaft sleeve.
GlandThe gland compresses the packing to maintain moderate contact with the shaft sleeve and control leakage. A split design allows packing replacement without dismantling other parts.Cast iron, cast steel or stainless steel, usually of split construction.
Bearing FrameThe bearing frame supports the bearing assembly, connects the pump end to the base and carries radial and axial loads. It is normally not a wear part.HT250 grey iron or QT500 ductile iron.
Impeller Release RingThe impeller release ring provides a bearing surface for removal, protecting impeller threads and the shaft end during on-site wear part changes.Quenched-and-tempered steel or stainless steel with sound threads.
Clamp WasherThe clamp washer spreads bolt or nut clamping force, protects mating faces and helps prevent loosening.Carbon steel, stainless steel or lock-type washers.
SELECTION

Matching structure and material to the duty

Common combinations; grade choice needs medium temperature, concentration and particle size.

Duty conditionRecommendation
Pumps with frequent maintenanceKeep one or two sets of gaskets, O-rings and fasteners
Corrosive environmentStainless fasteners prevent seizing during dismantling
High temperatureSelect gasket and O-ring material for the temperature
Older pumpsCheck drawings and actual dimensions instead of ordering by model only
MATCHING RANGE

Matching series and models

Model pages list construction, code explanation and chart extracts.

AH series
ZJ series
ZGB series
SP series
HH series
G series
DT series
RELATED PARTS

Parts in this category

Each part has its own page with basic number, material and matching range.

FAILURE MODES

How these parts fail and what to do

Judge by wall thickness, clearance and performance, not by months in service.

FAQ

Other Wear Parts questions

How should a spare-parts list be built?

Sort by pump and frame: wetted parts, seal parts, drive parts and small items. Set stock levels for each group based on wear rate and lead time.

Can small parts be ordered by model only?

Fasteners and gaskets can differ between batches, so the basic part number or actual dimensions should be confirmed.

How should spares be stored?

Rubber away from light and heat, metal parts protected from rust, seals stored flat and unloaded. Check rubber parts for ageing before use.

Inquiry

Send a model or worn-part dimensions

Parts are supplied by basic part number because the same name has different numbers in different frames. Send the pump model, frame code and a photo of the worn part, or the basic number directly.

Ask about Other Wear Parts

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry