Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Spare Parts/Wetted Parts/Rear Sheath
Rear Sheath
Rear Sheath — part photographBasic no. 036 / 043
SPARE PART

Rear Sheath

后护套

The rear sheath protects the transition between the drive-side chamber and the seal area, reducing vortex erosion and leakage risk.

Wetted PartsPart code 036 / 043
036 / 043Basic number
Wear-resistant alloyCommon material
Wetted PartsCategory
FUNCTION

What the rear sheath does

Function

The rear sheath protects the transition between the drive-side chamber and the seal area, reducing vortex erosion and leakage risk.

Location in the pump

Inside the drive side of the pump end, between the frame plate liner and the shaft seal assembly.

PART CODES

Part codes for the rear sheath

Basic number, common full part numbers, the complete code index and model-by-model references.

Basic part number / BASIC NO.
036 / 043

Rear rubber sheath

Common full part numbers

E4036RE4043R

Rear sheath is 036 (rubber) or 043 in the parts list, used with the 041 frame plate liner.

Three-digit basic numbers are fixed for each part type (147 impeller, 110 volute liner, 083 throatbush, 041 frame plate liner, 075 shaft sleeve, 005 bearing assembly). Prefixes vary with pump model and frame, and suffixes denote material: for example E4147 on a 6/4D-AH, F6147 on an 8/6E-AH and G8147 on a 10/8ST-AH. This index is compiled from published part code references for drawing checks and enquiries only; binding part numbers follow the supplied parts book and written confirmation.

Complete basic part number index

Part names link to their own pages; the current part is highlighted.

Show all basic numbersBy basic number
Basic no.Part nameGroup
001Adjusting boltDrive
003Bearing frameDrive
004Bearing housingDrive
005Bearing assembly / rotorDrive
009BearingDrive
011Clamp washerFasteners
012Clamp boltFasteners
013Cover plateWetted
015Cover plate studFasteners
018Front rubber sheathWetted
023Front sheath studFasteners
024End coverDrive
025End cover gasketSeal
026Frame plate liner boltFasteners
027End cover adjusting nutFasteners
028ExpellerSeal
029Relief coverSeal
032Casing / pump bodyWetted
034Casing boltFasteners
036Rear rubber sheathWetted
039Rear sheath studFasteners
040Frame plate liner boltFasteners
041Frame plate liner insertWetted
043Rear sheathWetted
044Split glandSeal
045Gland boltFasteners
046Grease retainerDrive
061Imperial round nutFasteners
062Labyrinth sleeveSeal
063Lantern ringSeal
064O-ringSeal
067Packing spacerSeal
073ShaftDrive
075 / 076Shaft sleeve / long sleeveSeal
078Stuffing boxSeal
080Register gasketFasteners
081Locating plateDrive
083ThroatbushWetted
085Locating wedgeWetted
089Bearing seal ringDrive
090Lip seal ringSeal
108Labyrinth ringSeal
109O-ringSeal
110Volute linerWetted
111PackingSeal
117SpacerDrive
118Front lantern ringSeal
122GasketFasteners
124Volute liner gasketWetted
125Frame plate liner gasketWetted
126Gland studFasteners
132Discharge gasketWetted
138Oil cup seatDrive
147ImpellerWetted

Part codes by pump model

Prefixes vary with pump model and frame. Both model and part names link to their own pages.

Show typical model code setsBy pump model
MATERIALS

Materials used for rear sheaths

Wetted parts contact the slurry directly and wear fastest. Impeller, volute liner, front liner and frame plate liner are normally evaluated as a set to maintain running clearances.

Material selection

Wear-resistant alloy or rubber lining, consistent with adjacent liners.

MaterialTypical dutySelection notes
High chrome alloy Cr26 / Cr27 / Cr30Coarse, sharp, highly abrasive ore slurry, tailings and ashVery hard and abrasion resistant; relatively brittle and not suited to large stray impacts
Natural / synthetic wear-resistant rubberFine particles, mildly acidic or alkaline corrosive slurry; noise and vibration dampingElastic and resistant to fine-particle cutting; vulnerable to sharp coarse solids and high temperature - check the temperature limit
Duplex stainless / high-nickel alloyStrongly corrosive, chloride-bearing or high-temperature specialty slurriesCorrosion resistance first; weigh service life and cost against abrasiveness
Polyurethane / ceramic compositeFine but highly abrasive particles, or lightweight wear solutionsLightweight and wear resistant, higher cost; always verify part number and dimensions
Metal vs. rubber parts
WEAR & SERVICE

Wear signs, inspection and replacement

01

Typical wear or failure signs

Erosion of seating faces, lining debonding or grooved sealing faces may come with increased leakage at the shaft seal.

02

Inspection and replacement

Inspect when servicing the shaft seal and verify fit with the frame plate liner and relief cover.

This section describes general slurry pump principles, selection and maintenance. It does not constitute a commitment regarding particular product parameters, materials, service life or scope of service. Binding values are those in the supplied documentation and in documents confirmed in writing by both parties.
DRAWINGS

Construction and exploded views

Enlarge the exploded and construction views to confirm assembly relationships.

Exploded view
Exploded view
Horizontal construction
Horizontal construction
Vertical construction
Vertical construction
APPLICABLE PUMPS

Applicable pump models

Part codes vary with frame and material; verify against model and part basic number before ordering.

All models
INQUIRY

Rear Sheath — quotation and part check

Send the model or worn-part dimensions, or call +86 188 0321 2220 / email sale@pumpq.com.

Request a price

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry