Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Spare Parts/Wetted Parts/Front Liner
Front Liner
Front Liner — part photographBasic no. 083
SPARE PART

Front Liner

前护板

The front liner (throatbush) protects the suction-side cover, forms the impeller inlet sealing face and controls inlet recirculation and suction-side wear.

Wetted PartsPart code 083
083Basic number
High-chrome wear alloyCommon material
Wetted PartsCategory
FUNCTION

What the front liner does

Function

The front liner (throatbush) protects the suction-side cover, forms the impeller inlet sealing face and controls inlet recirculation and suction-side wear.

Location in the pump

Located between the cover plate and the impeller eye, normally overlapping and aligning with the volute liner.

PART CODES

Part codes for the front liner

Basic number, common full part numbers, the complete code index and model-by-model references.

Basic part number / BASIC NO.
083

Throatbush

Common full part numbers

E4083F6083G8083EH3083G10083

Throatbush basic number 083; rubber versions are often written E4083R.

Three-digit basic numbers are fixed for each part type (147 impeller, 110 volute liner, 083 throatbush, 041 frame plate liner, 075 shaft sleeve, 005 bearing assembly). Prefixes vary with pump model and frame, and suffixes denote material: for example E4147 on a 6/4D-AH, F6147 on an 8/6E-AH and G8147 on a 10/8ST-AH. This index is compiled from published part code references for drawing checks and enquiries only; binding part numbers follow the supplied parts book and written confirmation.

Complete basic part number index

Part names link to their own pages; the current part is highlighted.

Show all basic numbersBy basic number
Basic no.Part nameGroup
001Adjusting boltDrive
003Bearing frameDrive
004Bearing housingDrive
005Bearing assembly / rotorDrive
009BearingDrive
011Clamp washerFasteners
012Clamp boltFasteners
013Cover plateWetted
015Cover plate studFasteners
018Front rubber sheathWetted
023Front sheath studFasteners
024End coverDrive
025End cover gasketSeal
026Frame plate liner boltFasteners
027End cover adjusting nutFasteners
028ExpellerSeal
029Relief coverSeal
032Casing / pump bodyWetted
034Casing boltFasteners
036Rear rubber sheathWetted
039Rear sheath studFasteners
040Frame plate liner boltFasteners
041Frame plate liner insertWetted
043Rear sheathWetted
044Split glandSeal
045Gland boltFasteners
046Grease retainerDrive
061Imperial round nutFasteners
062Labyrinth sleeveSeal
063Lantern ringSeal
064O-ringSeal
067Packing spacerSeal
073ShaftDrive
075 / 076Shaft sleeve / long sleeveSeal
078Stuffing boxSeal
080Register gasketFasteners
081Locating plateDrive
083ThroatbushWetted
085Locating wedgeWetted
089Bearing seal ringDrive
090Lip seal ringSeal
108Labyrinth ringSeal
109O-ringSeal
110Volute linerWetted
111PackingSeal
117SpacerDrive
118Front lantern ringSeal
122GasketFasteners
124Volute liner gasketWetted
125Frame plate liner gasketWetted
126Gland studFasteners
132Discharge gasketWetted
138Oil cup seatDrive
147ImpellerWetted

Part codes by pump model

Prefixes vary with pump model and frame. Both model and part names link to their own pages.

Show typical model code setsBy pump model
MATERIALS

Materials used for front liners

Wetted parts contact the slurry directly and wear fastest. Impeller, volute liner, front liner and frame plate liner are normally evaluated as a set to maintain running clearances.

Material selection

High-chrome wear alloy or rubber; metal parts are preferred for fine but highly abrasive solids.

MaterialTypical dutySelection notes
High chrome alloy Cr26 / Cr27 / Cr30Coarse, sharp, highly abrasive ore slurry, tailings and ashVery hard and abrasion resistant; relatively brittle and not suited to large stray impacts
Natural / synthetic wear-resistant rubberFine particles, mildly acidic or alkaline corrosive slurry; noise and vibration dampingElastic and resistant to fine-particle cutting; vulnerable to sharp coarse solids and high temperature - check the temperature limit
Duplex stainless / high-nickel alloyStrongly corrosive, chloride-bearing or high-temperature specialty slurriesCorrosion resistance first; weigh service life and cost against abrasiveness
Polyurethane / ceramic compositeFine but highly abrasive particles, or lightweight wear solutionsLightweight and wear resistant, higher cost; always verify part number and dimensions
Metal vs. rubber parts
WEAR & SERVICE

Wear signs, inspection and replacement

01

Typical wear or failure signs

Grooves on the inlet sealing face, an enlarged bore or rubber debonding increase recirculation and reduce flow and NPSH performance.

02

Inspection and replacement

Inspect the inlet clearance together with the impeller. On replacement, check gaskets and alignment to avoid uneven wear.

This section describes general slurry pump principles, selection and maintenance. It does not constitute a commitment regarding particular product parameters, materials, service life or scope of service. Binding values are those in the supplied documentation and in documents confirmed in writing by both parties.
DRAWINGS

Construction and exploded views

Enlarge the exploded and construction views to confirm assembly relationships.

Exploded view
Exploded view
Horizontal construction
Horizontal construction
Vertical construction
Vertical construction
APPLICABLE PUMPS

Applicable pump models

Part codes vary with frame and material; verify against model and part basic number before ordering.

All models
INQUIRY

Front Liner — quotation and part check

Send the model or worn-part dimensions, or call +86 188 0321 2220 / email sale@pumpq.com.

Request a price

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry