Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Slurry Pumps/HH Series High Head Slurry Pump/4/3E-HH
HH Series High Head Slurry Pump product sheet
HH Series High Head Slurry Pump product sheetModel 4/3E-HH
HH Series High Head Slurry Pump · Model details

4/3E-HH

HH Series High Head Slurry Pump

The HH series builds on the heavy duty slurry pump with thicker wear sections and heavier frames for higher single-stage head. It suits low-concentration/high-head or high-concentration/low-abrasion high-head duties, long-distance lines and series operation.

Horizontal Slurry PumpHorizontal, double-casing, high-head heavy duty slurry pumpFrame E
126–252Capacity Q m³/h
12–97Head H m
600–1400Speed r/min
MODEL CODE

Reading the code 4/3E-HH

Each segment explained against published industry naming conventions.

FieldMeaning
Suction bore4 in
Discharge bore3 in
Frame codeE (commonly published max. motor power about 120 kW)
Series codeHH
Model codes are explained against common industry naming conventions for reading the letters and numbers only. Bore sizes, frames, materials and performance of a specific build follow the supplied documents and written confirmation.
CONSTRUCTION & DUTIES

Construction and typical duties

HH Series High Head Slurry Pump

Construction

01

Thicker wear sections with a pump end designed for higher pressure duty.

02

Can be staged in series to raise total head.

03

Frames carry higher loads than a standard heavy duty pump of the same bore.

04

Wear-resistant metal wetted parts, with rotatable discharge positions.

Typical duties

01

Long-distance tailings and concentrate pipelines

02

Series-staged pressure boosting

03

High-head duties in metallurgy, chemical plants and dredging

Construction drawing
Slurry pump construction drawing
MATERIALS & SEALS

Wetted materials and shaft seals

Wetted materials

Primarily high-chrome wear alloy; rubber or corrosion-resistant alloys are evaluated against pH, temperature and chloride content when the medium is corrosive.

Shaft seal

Packing, expeller or mechanical seals. On high-head duty, seal-water pressure and the number of stages deserve particular attention.

This section describes general slurry pump principles, selection and maintenance. It does not constitute a commitment regarding particular product parameters, materials, service life or scope of service. Binding values are those in the supplied documentation and in documents confirmed in writing by both parties.
PERFORMANCE DATA

Performance data for 4/3E-HH

Clear-water data for this model, full series charts and notes from the manuals.

Model specification and technical parameters

ParameterValue / description
Suction bore4 in
Discharge bore3 in
Frame codeE (commonly published max. motor power about 120 kW)
Series codeHH
ConstructionHorizontal, double-casing, high-head heavy duty slurry pump
Wetted material optionsPrimarily high-chrome wear alloy; rubber or corrosion-resistant alloys are evaluated against pH, temperature and chloride content when the medium is corrosive.
Shaft seal optionsPacking, expeller or mechanical seals. On high-head duty, seal-water pressure and the number of stages deserve particular attention.
Published series coverageTypical coverage: discharge bores about 25-150 mm and single-stage head up to roughly 90-118 m.

4/3E-HH · rows in AH Series Pump Performance Chart · table 1 (1)

ModelMax. power kWQ m³/hQ L/sH mn r/minMax. eff. %NPSH mImpeller mm
4/3E-HH120126-25235-7012-97600-1400502-5508

Full performance charts for this series

Complete clear-water performance data for this series. Click to expand; tables scroll horizontally.

AH Series Pump Performance Chart · table 135 rows
ModelMax. power kWQ m³/hQ L/sH mn r/minMax. eff. %NPSH mImpeller mm
1.5/1B-AH1512.6-28.83.5-86-681200-3800402-4152
2/1.5B-AH1532.4-729-206-581200-3200453.5-8184
3/2C-AH3039.6-86.411-2412-641300-2700554-6214
4/3C-AH3086.4-19824-559-521000-2200714-6245
4/3D-AH6086.4-19824-559-521000-2200714-6245
6/4D-AH60162-36045-10012-56800-1550655-8365
6/4E-AH120162-36045-10012-56800-1550655-8365
8/6E-AH120360-828100-23010-61500-1140722-9510
8/6R-AH300360-828100-23010-61500-1140722-9510
10/8ST-AH560612-1368170-38011-61400-850714-10686
12/10ST-AH560936-1980260-5507-68300-800826762
14/12ST-AH5601260-2772350-77013-63300-600773-10965
16/14TU-AH1201368-3060380-85011-63250-550794-101067
20/18TU-AH12002520-5400700-150013-57200-400855-101370
1.5/1B-AH1510.8-25.23-77-521400-3400352-4152
2/1.5B-AH1525.2-547-155.5-411000-2600502.5-5178
3/2C-AH3036-75.610-2113-391300-2100552-4213
4/3C-AH3079.2-18022-505-34.5800-1800593-5245
4/3D-AH6079.2-18022-505-34.5800-1800593-5245
6/4D-AH60144-32440-9012-45800-1350653-5365
6/4E-AH120144-32440-9012-45800-1350653-5365
8/6E-AH120324-72090-2007-49400-1000655-10510
8/6R-AH300324-72090-2007-49400-1000655-10510
10/8ST-AH560540-1188150-33012-50400-750754-12686
12/10ST-AH560720-1620200-4507-45300-650802.5-7.5762
14/12ST-AH5601152-2520320-70013-44300-500793-8965
16-14TU-AH12001224-2754340-7659-43250-450823-81067
20-18TU-AH12002268-4860630-135011-46200-350822-81372
10/8E-M120540-1440150-40014-60600-1000734-10549
10/8R-M300540-1440150-40014-60600-1000734-10549
1.5/1C-HH3016.2-34.24.5-9.525-921400-2200202-5.5330
3/2D-HH6068.4-136.819-3825-87850-1400473-7.5457
4/3E-HH120126-25235-7012-97600-1400502-5508
6/4F-HH260324-72090-20030-118600-1000643-8711
8/6S-HH560468-1008130-28020-94500-1000654-12711
Clear-water performance data for reference only; binding values follow the supplied technical documents and written confirmation.
FROM THE MANUAL

Notes from the product manuals

Compiled from the AH / L / G, SP, ZJ and ZGB pump manuals, with links to the full texts.

General construction, installation and operation

01 · Overview and scope

Horizontal slurry pumps are overhung centrifugal pumps for abrasive or corrosive slurry, widely used in metallurgy, mining, petrochemical, coal, power, dredging, building materials and municipal works. Families cover heavy duty (AH, HH), light duty (L), gravel / dredging (D, G) and rubber-lined (AHR, LR, MR) builds. Pumps may be staged in series within the allowable working pressure.

02 · Construction

Heavy duty AH and HH pumps use a double casing: an outer pressure-retaining casing and cover in grey or ductile iron, vertically split and bolted, plus replaceable wear liners (impeller, volute liner, throat bush and frame plate liner) in metal or rubber. The discharge can be rotated in eight positions at 45 degree intervals. D and G gravel pumps use a single casing with all wetted parts in wear-resistant metal. Apart from the wet end, all horizontal types share the same frame and bearing assembly, with a large-diameter shaft and short overhang.

03 · Assembly and installation

Preheat bearing inner rings to no more than 120 C during assembly and seat them firmly against the shaft shoulder or grease retainer. Inner rings, outer rings and spacers of double-row tapered roller bearings form a matched set and must not be interchanged. Wet-end assembly order: seals, frame plate liner with its locating nuts, impeller, volute liner clamped in place, then throat bush and cover plate. Lift crated pumps by the marked sling points without shock or excessive tilt; lifting eyes on the casing are for dismantling the casing only, never for lifting the complete pump.

04 · Shaft seal and lubrication

Three shaft seal arrangements are common: expeller, packed gland and mechanical seal. The expeller seal suits single-stage pumps (or the first stage of a series set) where inlet positive pressure is below 10 percent of discharge pressure; it needs no seal water and does not dilute the slurry. A packed gland is simple to service but requires seal water. A mechanical seal gives the best sealing and requires cooling water. A packed gland comprises the stuffing box, shaft sleeve, spacer, O-rings, packing, packing spacer, lantern ring and gland. Bearings are grease or oil lubricated, with oil lubrication preferred for high temperature or large pumps.

05 · Start-up and operation

Before start-up check that foundation and coupling bolts are tight, turn the shaft by hand in the direction of rotation without rubbing, verify motor rotation against the arrow on the casing, and align the V-belts square to the pulleys. Starting on clean water is preferable before slurry is introduced. During operation watch the instruments for flow, velocity and current and correct any abnormality. Where possible flush with clean water before stopping, then stop the pump before closing the valve. For vertical sump pumps, turn on the guide bearing flush water five minutes before starting and close it five minutes after stopping.

06 · Maintenance and faults

Check impeller-to-throatbush clearance, bearing temperature and lubrication, seal water pressure and flow, and wear of wetted parts on a regular basis. A worn impeller reduces flow and head and raises vibration and noise, so adjust the clearance or replace the wear parts. Typical faults are insufficient flow or head, bearing overheating, vibration, seal leakage and cavitation, usually caused by blockages, wrong rotation, low speed, air ingress on the suction side, inadequate NPSH or loss of dynamic balance. Record basic part numbers and material suffixes and verify them against the pump model and supplied documents.

Series-specific notes for HH Series High Head Slurry Pump

01

HH pumps suit low-concentration high-head slurry or high-concentration mildly abrasive high-head slurry. They share the double-casing heavy duty construction and drive end with the AH series.

02

Pumps may be staged in series within the maximum allowable working pressure; seal water pressure must be checked for each stage.

Source text excerpts

Original manual text

Extracts from the original manuals are shown in the Chinese edition; the full texts are available via the links below.

Read the source documents online

WEAR PARTS

Wear parts for this series

Open each part page for function, material and replacement notes.

INQUIRY

4/3E-HH — quotation and part check

Send the model or worn-part dimensions, or call +86 188 0321 2220 / email sale@pumpq.com.

Request a price

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry